Just How to Install a Bath Tub in Your Bathroom
Just How to Install a Bath Tub in Your Bathroom
Blog Article
Right here down the page you will find some reliable facts in relation to How to Install a Bathtub.
Mounting a bath tub isn't specifically brain surgery, yet it does call for strong plumbing, woodworking, and also occasionally, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably tough job. If the old bathtub is easily easily accessible, the project can move speedily; if you have to open up a wall to remove the old bathtub and also position the new bath tub, the job is much harder. In either case, the task is within a residence handyman's skills, although you will certainly need a helper to move out the old tub and also embeded in the brand-new one. Ensure you have certified yourself for the job and fit attempting it. Rather than hiring a contractor to take over a halfway-completed project, it is better to take into consideration using one prior to you start. Possibilities are you may require an expert plumber to make tube connections.
This article will aid you mount a brand-new tub in your restroom if you have already bought a brand-new bathtub as well as don't need to transform the setup of your previous water system pipelines.
Your tools and material list need to make up the following:
Planning for the Setup
Firstly, the sustaining frame provided with the bath needs to be fitted (if needed) according to the manufacturer's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to see to it that if the tap features a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets unit to stop strain on the bath tub.
Fit the flexible tap adapters to the bottom of the two faucets using 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you make use of every one of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its last setting.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your setup, then the first thing you must do is separate the water system. After doing so, turn on the taps to drain pipes any water staying in the system. The procedure of removing the existing taps can be rather bothersome due to the restricted accessibility that is often the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the faucets. Have a towel ready for the staying water that will certainly originate from the pipes. When the supply pipelines have actually been removed, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from turning throughout this procedure. Once the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any type of old securing compound.
Prior to going on to fit the brand-new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bathtub
Using the two wooden boards under its feet, put the tub in the needed placement. The wood boards are helpful in evenly spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto 4 little factors.
The next goal is to guarantee that the tub is leveled all round. This can be achieved by checking the spirit level and also readjusting the feet on the bath tub up until the spirit level checks out level.
To install faucets, fit all-time low of the outermost versatile tap connector to the appropriate supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Turn on the water system and check all joints and also brand-new pipework for leakages and also tighten them if required. Fill the bathtub as well as likewise check the overflow electrical outlet and also the typical outlet for leaks.
Ultimately, take care of the bath paneling as defined in the supplier's user's manual. Tiling and securing around the tub ought to wait until the bath tub has been utilized a minimum of once as this will certainly resolve it into its final placement.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to prevent damages to the string. One end of the connector fits on the plastic tail of the tap and also the various other end offers a connection to the current supply pipes.
If you require to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, place the faucet in the mounting opening in the bath/basin making sure that the washers are in area between the tap and also the sink. Protect the tap in position with the producer provided backnut. As soon as the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular faucet adapters. The former kind should be linked to the faucet ends initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath fulfills the tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture a stiff seal, creating the water to permeate the wall surface between the bathroom as well as the tiling, bring about problems with wetness and feasible leaks to the ceiling below.
You can pick from a variety of coloured sealers to blend in your components and also fittings. They are offered in tubes and also cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of soaked paper or soft rope. Remember to always load the bathtub with water prior to securing, to allow for the activity experienced when the bathtub is in usage. The sealer can break relatively very early if you do not consider this motion before sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the marketplace. It is advisable to fit the floor tiles using water-resistant or water-proof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you really like reading up on Installing A Bathtub? Write feedback directly below. We would be interested to find out your reactions about this write up. We are looking forward to see you back again in the future. Make sure you take the opportunity to share this entry if you liked it. Thanks so much for going through it.
Course Detail Report this page